自動噴粉的調節方法因設備類型和品牌的不同而有所差異，但以下是一些通用的調整步驟和注意事項：

　　The adjustment method for automatic powder spraying varies depending on the type and brand of equipment, but the following are some common adjustment steps and precautions:

　　設備啟動 ：

　　Device startup:

　　打開總電源，確認電源指示燈亮起。

　　Turn on the main power and confirm that the power indicator light is on.

　　依次開啟離心風機、濾風、逆風翻盤等旋鈕開關。

　　Turn on the rotary switches for centrifugal fan, air filter, and reverse wind flap in sequence.

　　緩慢調整靜電噴粉工作電壓至50KV-80KV，通?？刂圃?0-70KV。

　　Slowly adjust the working voltage of electrostatic powder spraying to 50KV-80KV, usually controlled at 60-70KV.

　　噴粉操作 ：

　　Powder spraying operation:

　　保持噴槍與工件的距離在15-30厘米之間。

　　Keep the distance between the spray gun and the workpiece between 15-30 centimeters.

　　根據噴涂質量，適時調整工藝參數。

　　Adjust the process parameters in a timely manner based on the spraying quality.

　　禁止用靜電噴粉頭去轉動工件。

　　It is prohibited to use an electrostatic powder nozzle to rotate the workpiece.

　　設備關閉 ：

　　Device shutdown:

　　工作結束或停工待料時，將靜電產生控制柜電流電壓調整至“0”。

　　Adjust the current and voltage of the static electricity generation control cabinet to "0" when the work is completed or stopped for materials.

　　針對不同類型噴粉設備的調節方法：

　　Adjustment methods for different types of powder spraying equipment:

　　噴粉機器人

　　Powder spraying robot

　　調節噴涂氣壓 ：

　　Adjust the spray pressure:

　　大霧化：將噴涂氣壓調節旋鈕處于槍體平行位置，順時針旋轉以減小噴涂氣壓。

　　Large atomization: Place the spray pressure adjustment knob parallel to the gun body and rotate it clockwise to reduce the spray pressure.

　　小霧化：將噴涂氣壓調節旋鈕處于槍體垂直位置，逆時針旋轉以增大噴涂氣壓。

　　Small atomization: Place the spray pressure adjustment knob in the vertical position of the gun body and rotate counterclockwise to increase the spray pressure.

　　調節涂料流量 ：

　　Adjust the paint flow rate:

　　增大涂料流量：逆時針旋轉涂料流量調節旋鈕，增大槍針行程。

　　Increase paint flow: Rotate the paint flow adjustment knob counterclockwise to increase the needle stroke.

　　減小涂料流量：順時針旋轉涂料流量調節旋鈕，減小槍針行程。

　　Reduce paint flow: Rotate the paint flow adjustment knob clockwise to decrease the needle stroke.

　　調節噴涂距離 ：

　　Adjust the spraying distance:

　　傳統噴槍：18~23厘米。

　　Traditional spray gun: 18-23 centimeters.

　　RP噴槍：15~23厘米。

　　RP spray gun: 15-23 centimeters.

　　HVLP噴槍：13~17厘米。

　　HVLP spray gun: 13-17 centimeters.

　　調節噴幅（扇面） ：

　　Adjust the spray amplitude (fan surface):

　　增大噴幅：逆時針旋轉噴幅調節旋鈕。

　　Increase spray amplitude: Rotate the spray amplitude adjustment knob counterclockwise.

　　減小噴幅：順時針旋轉噴幅調節旋鈕。

　　Reduce spray amplitude: Rotate the spray amplitude adjustment knob clockwise.

　　手動噴粉設備

　　Manual powder spraying equipment

　　調整噴涂參數 ：

　　Adjust spraying parameters:

　　根據噴涂物料的特性和噴涂效果要求，調整噴涂壓力、噴嘴大小、噴涂速度等。

　　Adjust the spraying pressure, nozzle size, spraying speed, etc. according to the characteristics of the spraying material and the requirements of the spraying effect.

　　調整噴槍與噴涂物料的距離，通常為20-30厘米。

　　Adjust the distance between the spray gun and the sprayed material, usually 20-30 centimeters.

　　預熱設備 ：

　　Preheating equipment:

　　使用前需預熱，預熱時間一般為10-15分鐘，以確保設備正常工作和達到較好的噴涂效果。

　　Preheating is required before use, usually for 10-15 minutes, to ensure normal operation of the equipment and achieve good spraying effect.

　　注意除塵 ：

　　Pay attention to dust removal:

　　噴涂前需將噴霧室內物品清潔干凈，以減少粉末的浪費和對操作人員的身體影響。

　　Before spraying, the articles in the spray room should be cleaned to reduce the waste of powder and the physical impact on operators.

　　通用注意事項

　　General precautions

　　電壓和電流調節 ：

　　Voltage and current regulation:

　　電壓的調節范圍通常在50KV到100KV之間，具體根據噴粉顏色和厚度調整。

　　The voltage adjustment range is usually between 50KV and 100KV, depending on the color and thickness of the powder coating.

　　電流的調節范圍在10uA到100uA之間，具體根據噴粉速度和距離調整。

　　The adjustment range of the current is between 10uA and 100uA, depending on the powder spraying speed and distance.

　　噴槍清洗 ：

　　Spray gun cleaning:

　　噴涂完成后，及時清洗噴槍，以免堵塞或損壞噴嘴。

　　After spraying, clean the spray gun in a timely manner to avoid clogging or damaging the nozzle.

　　通過以上步驟和注意事項，可以有效地調整自動噴粉設備，以達到最佳的噴涂效果。建議根據具體設備的使用說明書和實際操作經驗進行微調，并在實際操作中不斷嘗試和優化參數。

　　By following the above steps and precautions, the automatic powder spraying equipment can be effectively adjusted to achieve the best spraying effect. It is recommended to make minor adjustments based on the specific device's user manual and practical operating experience, and continuously try and optimize parameters in actual operation.

　　本文來自：自動噴粉線更多的內容請點擊：http://www.hbrqhj.com我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！

　　This article is from: Automatic powder spraying line. For more content, please click: http://www.hbrqhj.com We will provide satisfactory service for the questions you ask. Welcome to call us!

上一篇：關于焊煙除塵設備的介紹
下一篇：車間整體除塵設備：除塵后該如何進行消毒殺菌來保持干凈衛生